Filter
Top Products
EL EE ELEE
TO MS TOMS
CRCOTCRCOT
AATT AATT
RNRE RNRE
RSLMRSLM
IRXCMRDO IRXCMRDO
ECMT I C WD ECMT I CWD
RVTSTV NE RVTS TVNE
#XX# #XX#
5.2.5
Voice/Fax Channel Commands
The Voice/Fax Channel commands control the traffic of the voice and fax communication over the composite link network. The
Voice/Fax Channel commands are described in detail below:
List The Voice/Fax List The Voice/Fax Channel Parameters command causes the
Channel MultiMux to display the parameters for the Voice/Fax channels
Parameters on the system's supervisory console as shown in the following example. The Voice/
Fax channel parameters display general VL parameters for both channels and the local and remote channel
interfaces. To display the parameters for the Voice/Fax channels, you would enter ATVL
and hit your Return key.
LOCAL VOICE/FAX PARAMETERS CHANNEL1 LOCAL VOICE/FAX PARAMTERS CHANNEL 2
PARAMETER STATUS PARAMETER STATUS
DESTINATION CHANNEL 01 DESTINATION CHANNEL 02
DESTINATION NODE 01 DESTINATION NODE 01
LINK A/B/D A LINK A/B/D A
DIGITIZING RATE 16000 DIGITIZING RATE 16000
OUTPUT LEVEL ATTEN. 12 OUTPUT LEVEL ATTEN. 12
INPUT LEVEL GAIN 03 INPUT LEVEL GAIN 03
SILENCE SUPPRESSION 02 SILENCE SUPPRESSION 02
LOCAL INTERFACE TYPE FXS LOCAL INTERFACE TYPE FXS
GROUND/LOOP START (FXS) LOOP GROUND/LOOP START (FXS) LOOP
2 OR 4 WIRE (E&M) 2 WIRE 2 OR 4 WIRE (E&M) 2 WIRE
DIALTONE/WINK (E&M) N/A DIALTONE/WINK (E&M) N/A
WINK TIMER N/A WINK TIMER N/A
REMOTE INTERFACE TYPE FXS REMOTE INTERFACE TYPE FXS
GROUND/LOOP START (FXS) LOOP GROUND/LOOP START (FXS) LOOP
2 OR 4 WIRE (E&M) 2 WIRE 2 OR 4 WIRE (E&M) 2 WIRE
DIALTONE/WINK (E&M) N/A DIALTONE/WINK (E&M) N/A
Reset The Reset Voice/Fax Channel command sets the operating
Voice/Fax parameters for the voice/fax channel to the most recently
Channel stored values and resets that channel.
V(1/2)Z
Voice/Fax The Voice/Fax Destination Channel command selects which
Destination voice/fax channel (1 or 2) on the destination MultiMux will receive
Channel the voice/fax information. Local voice channel 1 (V1) can select
V(1/2)DC destination channel 1 DC1 or destination channel 2 DC2 to receive the information.
Similarily, V2 can select DC1 or DC2.
Voice/Fax The voice/Fax Destination Node command (V(1/2)DN(0-31))
Destination Node selects the destination MultiMux (0-31) for which voice/fax data will be sent. The voice/
fax channels 1 or 2 can select destination V(1/2)DN nodes from 0 to 31. Voice/fax channel 1 can select a
destination node of 25 using V1DN25 command.
Link the Voice/Fax The Link the voice/Fax Channel will Communicate Over command
Channel will (V(1/2)ML(A/B/D)) selects the composite link (A/B/D) in which
Communicate Over the voice/fax data will be sent. Local voice/fax channel 1 can send voice/fax data
over composite link A by executing V1MLA V(1/2)ML command. The V2MLD command enables voice/fax channel