Filter
Top Products
SECTION 105-R
VILTER MANUFACTURING CORPORATION
February 2001
PAGE 13
Replaces
440 VMC COMPRESSORS
July 1986
REAR BEARING COVER REPLACEMENT PARTS (Compressors With Standard Tri-Micro
®
Filter)
NO. REQ. PER COMPRESSOR SERIAL NO.
ITEM DESCRIPTION
SINGLE STAGE
TWO-
STAGE
PART
NO. OF CYL.
2 4 6 8 12 16 6 12 FROM THRU NUMBER
301
Thru Rear Bearing Cover Assembly Kit 1 1 1 1 1 1 1 1 0 Present KT092
304
301 Cover, Rear Bearing 1 1 1 1 1 1 1 1 0 Present **
302 Plug, ¾” Hex. Socket Head Pipe 1 1 1 1 1 1 1 1 0 Present 13163E
303 Pin,
3
/
8
” x 1” Dowel (not shown) 1 1 1 1 1 1 1 1 0 Present 2868H
304 Orifice, Oil Metering (not shown) 1 1 1 1 1 1 1 1 0 Present 33361A
305 Gasket, Oil Pump body 1 1 1 1 1 1 1 1 0 Present 31899A
306 Oil Pump Assembly 1 1 1 1 1 1 1 1 0 Present A33480A
307
Thru Conversion Kit, Std. Tri-Micro 1 1 1 1 1 1 1 1 0 13374 KT361A &
B +
324
307 Gasket, Oil Pump Cover 1 1 1 1 1 1 1 1 0 Present 31900A
308 Gasket, Oil Pump and Rear Bearing
Cover Seal
1 1 1 1 1 1 1 1 13375 Present 33320A
309 Cover, Oil Pump and Filter Head
(Used when Oil Cooler not used) 1 1 1 1 1 1 1 1 13375 Present 36190A
309 Cover, Oil Pump and Filter Head
(Used when Oil Cooler is used) 1 1 1 1 1 1 1 1 13375 Present 34759A
310 Filter Assy, Complete (Tri-Micro) 1 1 1 1 1 1 1 1 13375 Present A35240A
(Items 311 thru 322B)
311, 312,
313 &
314
Spool – Strainer Tube Assembly
1
1
1
1
1
1
1
1
13375
Present
1448U
311, 312
thru 314
& 315
thru 319
&321
Filter Assembly (without
shell)
1
1
1
1
1
1
1
1
13375
Present
1448T
311 Spool Assembly (with bypass relief) 1 1 1 1 1 1 1 1 13375 Present 1448J
312 Seal, Spool End 1 1 1 1 1 1 1 1 13375 Present 1448H
313 Strainer Tube 1 1 1 1 1 1 1 1 13375 Present 1448K
314 Ring, Retaining 1 1 1 1 1 1 1 1 13375 Present 1448L
315 Recharge (Gasket 1448B included) 1 1 1 1 1 1 1 1 13375 Present 1448C
316 Pressure Plate Assembly 1 1 1 1 1 1 1 1 13375 Present 1448M
(Items 317, 318 and 319)
317 Pressure Plate 1 1 1 1 1 1 1 1 13375 Present 1448N
318 ‘O’ Ring Seal, Pressure Plate 1 1 1 1 1 1 1 1 13375 Present 1448P
319 Spring, Pressure Plate 1 1 1 1 1 1 1 1 13375 Present 1448Q
320 Plug, Steel Square Head Pipe, 1/8” 1 1 1 1 1 1 1 1 13375 Present 13264A
321 Gasket, Oil Filter Head 1 1 1 1 1 1 1 1 13375 Present 1448B
322 Filter Shell with Flange and Plug 1 1 1 1 1 1 1 1 13375 Present A34623A
(Items 320, 322A and 322B)
322A Flange, Oil Filter Tank 1 1 1 1 1 1 1 1 13375 Present 35125A
322B Tank, Oil Filter 1 1 1 1 1 1 1 1 13375 Present 34623A
323 Screw, Hex. Head Cap
7
/
16
” x 2” 4 4 4 4 4 4 4 4 13375 Present 1689G
324 Instruction/Name Plate (not shown) 1 1 1 1 1 1 1 1 13375 Present 40680AT
325 Gasket, Bearing Cover 1 1 1 1 1 1 1 1 0 Present 31890A
326 Screw,
5
/
8
” x 2” Hex. Head Cap 10 10 10 10 10 10 10 10 0 Present 13152E
327 Screw, ½” x 1¾”Hex Head Cap 8 8 8 8 8 8 8 8 0 Present 2796EL
NOTES:
A. “Tri-Micro” is a registered trademark of Vilter Manufacturing Corporation.
** The rear bearing cover is sold only in Kit KT092.
+ When Kit KT256 is ordered, the overall length of the existing oil pump (Item 306) on the compressor should be checked. If the
length from the end of the pump shaft to the end of the pump boss measures 5
7
/
32
”, a new oil pump must be ordered with Kit
KT256.