Filter
Top Products
SECTION 105-R
VILTER MANUFACTURING CORPORATION
February 2001
PAGE 15
Replaces
440 VMC COMPRESSORS
February 1984
REAR BEARING COVER REPLACEMENT PARTS
Compressors With Special (Improved) Tri-Micro
®
Filter Option
NO. REQ. PER COMPRESSOR SERIAL NO.
ITEM DESCRIPTION
SINGLE STAGE
TWO-
STAGE
PART
NO. OF CYL.
2 4 6 8 12 16 6 12 FROM THRU NUMBER
301 thru Rear Bearing Cover Assembly Kit 1 1 1 1 1 1 1 1 0 Present KT092
304
301 Cover, Rear Bearing 1 1 1 1 1 1 1 1 0 Present **
302 Plug, ¾” Hex Socket Head Pipe 1 1 1 1 1 1 1 1 0 Present 13163E
303 Pin,
3
/
8
” x 1” Dowel (not shown) 1 1 1 1 1 1 1 1 0 Present 2868H
304 Orifice, Oil Metering (not shown) 1 1 1 1 1 1 1 1 0 Present 33361A
305 Gasket, Oil Pump Body 1 1 1 1 1 1 1 1 0 Present 31899A
306 Oil Pump Assembly 1 1 1 1 1 1 1 1 0 Present A33480A
307 Conversion Kit, Special (improved) 1 1 1 1 1 1 1 1 0 Present KT361A +
Thru Tri-Micro Oil Filter, 120 volts
339 Conversion Kit, Special (improved) 1 1 1 1 1 1 1 1 0 Present KT361B +
Tri-Micro Oil filter, 240 volts
307 Gasket, Oil Pump Cover 1 1 1 1 1 1 1 1 0 Present 31900A
308 Gasket, Oil Pump and Rear Bearing
Cover Seal
1 1 1 1 1 1 1 1 0 Present 33320A
309 Cover, Oil Pump and Filter Head 1 1 1 1 1 1 1 1 0 Present 34565A
310 Filter Assembly, Complete (Tri-Micro) 1 1 1 1 1 1 1 1 0 Present A35241A
311 Spool Assembly (without bypass relief) 1 1 1 1 1 1 1 1 0 Present 2046A
312 Seal, Spool End 1 1 1 1 1 1 1 1 0 Present 1448H
313 Strainer Tube 1 1 1 1 1 1 1 1 0 Present 1448K
314 Ring, Retaining 1 1 1 1 1 1 1 1 0 Present 1448L
315 Recharge (Gasket 1448B included) 1 1 1 1 1 1 1 1 0 Present 2115C
316 Pressure Plate Assembly 1 1 1 1 1 1 1 1 0 Present 1448M
317 Pressure Plate 1 1 1 1 1 1 1 1 0 Present 1448N
318 ‘O’ Ring Seal, Pressure Plate 1 1 1 1 1 1 1 1 0 Present 1448P
319 Spring, Pressure Plate 1 1 1 1 1 1 1 1 0 Present 1448Q
320 Plug, Steel Square Head Pipe
1
/
8
” 1 1 1 1 1 1 1 1 0 Present 1190A
321 Gasket, Oil Filter Head 1 1 1 1 1 1 1 1 0 Present 1448B
322 Filter Shell with Bolt Ring 1 1 1 1 1 1 1 1 0 Present A34623A
323 Screw, Hex Head Cap
7
/
16
” x 2” 4 4 4 4 4 4 4 4 0 Present 1689G
324 Instruction/Nameplate 1 1 1 1 1 1 1 1 0 Present 40680AJ
325 Gauge, 2½”, 0-300 PSI, Oil Filter 1 1 1 1 1 1 1 1 0 Present 2047A
326 Elbow, ¼” 90° Female Compression 1 1 1 1 1 1 1 1 0 Present 1892B
327 Tubing, ¼” O.D. x 5 ft. Steel AR AR AR AR AR AR AR AR 0 Present S1589A
328 Tee, ¼” Compression 2 2 2 2 2 2 2 2 0 Present 13239C
329 Connector, ¼”MPT X ¼”O.D. Compression 3 3 3 3 3 3 3 3 0 Present 13229D
330 Valve, 3-Way, Oil Filter 1 1 1 1 1 1 1 1 0 Present 2030A
331 Bracket, Valve 1 1 1 1 1 1 1 1 0 Present 35106A
332 Elbow, ¼” 90° Male Compression 1 1 1 1 1 1 1 1 0 Present 13375D
333 Control, Pressure Differential 1 1 1 1 1 1 1 1 0 Present 1643V
334 Screw, 10-32 x
3
/
8
” Long, Round Head 2 2 2 2 2 2 2 2 0 Present 1332C
335 Washer, Lock,
3
/
16
” 2 2 2 2 2 2 2 2 0 Present 13165A
336 Washer, Flat,
3
/
16
” 4 4 4 4 4 4 4 4 0 Present 13265A
337 * Cover, Crankcase Handhole 1 1 1 1 1 1 1 1 0 Present A33034L
338 * Thermometer, Crankcase Oil 1 1 1 1 1 1 1 1 0 Present 1467F
339 * Heater, 535W, 115V Electric Crankcase 1 1 1 1 1 1 1 1 0 Present 2069J
339 * Heater, 535W, 230V Electric Crankcase 1 1 1 1 1 1 1 1 0 Present 2069K
340 Gasket, Bearing Cover 1 1 1 1 1 1 1 1 0 Present 31890A
341 Screw,
5
/
8
” x 2” Hex Head Cap 10 10 10 10 10 10 10 10 0 Present 13152E
342 Screw, ½” x 1¾” Hex Head Cap 8 8 8 8 8 8 8 8 0 Present 2796EL
NOTES:
AR = As required. Cut to suit when assembling.
• Not shown here, cover replaces item 123. Thermometer and heater mount on crankcase handhole cover so oil temperature
can be monitored and raised to 100°F (thermostat setting) before starting compressor. If an attempt is made to start with cold
oil, the filter pressure differential switch will stop compressor.
** The rear bearing cover is sold only in Kit KT092.
+ When Kit KT361A & B is ordered, the overall length of the existing oil pump (Item 306) on the compressor should be checked.
If the length from the end of the pump shaft to the end of the pump boss measures 5
7
/
32
”, a new oil pump must be ordered with
Kit KT361A & B.