Filter
Top Products
OPTIONS/ACCESSORIES
The following options/accessories are available for
your Commander 400 from your local Lincoln
Distributor.
K802R Power Plug Kit - Provides a plug for each
receptacle. The kit includes 4-120V plugs rated at 15
Amps each and 1-120V/240V Full-KVA plug rated at 50
Amps.
K857 28 ft. (8.5 m) or K857-1 100 ft. (30.4 m) Remote
Control - Portable control provides same dial range as
the output control on the welder from a location up to
the specified length from the welder. Has convenient
plug for easy connection to the welder. The
Commander 400 is equipped with a 6 pin connector for
connecting the remote control and a toggle switch for
selecting “LOCAL” output control or “REMOTE” output
control.
K704 Accessory Kit - Includes 35 feet (10 m) of elec-
trode cable and 30 feet (9 m) of work cable, head
shield, work clamp and electrode holder. Cable is
rated at 500 amps, 60% duty cycle.
K953-1 Two Wheel Trailer - For road, in-plant and
yard towing. Road towing with optional fender & light
kit. (For highway use, consult applicable federal, state
and local laws regarding possible additional require-
ments.)
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit
K965-1 Cable Storage Rack
K825-1 Ether Start Kit - Provides maximum cold
weather starting assistance for frequent starting below
10
o
F (-12.2
o
C). Required Ether tank is not provided
with kit.
K899-1 Spark Arrestor Kit - Easily mounts to stan-
dard muffler.
K949-1 Oil Drain Kit - Includes ball valve, hose and
clamp.
STICK WELDING
K704 Accessory Kit which includes:
• Electrode holder and cable.
• Ground clamp and cable.
• Head shield.
TIG WELDING
Magnum TIG Torch
Magnum Parts Kit and Argon gas
K930-1 TIG Module (not required for scratch
start DC TIG welding)
K936-3 Control Cable
K870 Foot Amptrol
Also available:
K963 Hand Amptrol
K814 Arc Start Switch
K937-22 Control Cable Extension
K937-45 Control Cable Extension
K844-1 Water Valve
HIGH FREQUENCY GENERATORS FOR TIG
APPLICATIONS
The K799 Hi-Freq Unit and the K930-1 TIG Module are
suitable for use with the Commander 400. The
Commander is equipped with the required R.F. bypass
circuitry for the connection of high frequency generat-
ing equipment. The high frequency bypass network
supplied with the K799 Hi-Freq Unit does NOT need
to be installed into the Commander 400.
The Commander 400 and any high frequency generat-
ing equipment must be properly grounded. See the
K799 Hi-Freq Unit and the K930-1 TIG Module operat-
ing manuals for complete instructions on installation,
operation, and maintenance.
SEMIAUTOMATIC WELDING ACCESSORIES
LN-25 Wire Feeder - This portable wire feeder is capa-
ble of CC/CV wire feed welding.
LN-7 or LN-8 Wire Feeders - Semiautomatic, constant
speed wire feeder. For CV operation only.
LN-23P Wire Feeder - This portable wire feeder is
capable of CV operation. K350-1 adapter kit is
required.
NOTE: Gas-shielded welding requires a Magnum Gun.
Gasless welding requires an Inner shield Gun.
Magnum Spool Gun (K487-25) - A lightweight, semi-
automatic wire feeder for aluminum welding with argon
gas. Has built-in remote wire speed control in the han-
dle. Requires the K488 SG Control Module with appro-
priate control cable. Includes 25 feet (7.6 meters) of
power cable.
ACCESSORIES
C-2 C-2
COMMANDER 400
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC
Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC