Filter
Top Products
xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
85
offset_chunk_1 - Specifies the contents of the offset trunk 1 to be monitored.
<hex 0x0-0xffffffff> - Enter the contents of the offset trunk 1 to be monitored here.
mask - Specifies an additional mask for each field.
<hex 0x0-0xffffffff> - Enter the additional mask value used here.
offset_chunk_2 - Specifies the contents of the offset trunk 2 to be monitored.
<hex 0x0-0xffffffff> - Enter the contents of the offset trunk 2 to be monitored here.
mask - Specifies an additional mask for each field.
<hex 0x0-0xffffffff> - Enter the additional mask value used here.
offset_chunk_3 - Specifies the contents of the offset trunk 3 to be monitored.
<hex 0x0-0xffffffff> - Enter the contents of the offset trunk 3 to be monitored here.
mask - Specifies an additional mask for each field.
<hex 0x0-0xffffffff> - Enter the additional mask value used here.
offset_chunk_4 - Specifies the contents of the offset trunk 4 to be monitored.
<hex 0x0-0xffffffff> - Enter the contents of the offset trunk 4 to be monitored here.
mask - Specifies an additional mask for each field.
<hex 0x0-0xffffffff> - Enter the additional mask value used here.
ipv6 - Specify that the rule applies to IPv6 fields.
class - Specify the value of the IPv6 class.
<value 0-255> - Specify the value between 0 and 255.
flowlabel - Specify the value of the IPv6 flow label.
<hex 0x0-0xfffff> - Specify the value of the IPv6 flow label.
source_ipv6 - Specify the value of the IPv6 source address.
<ipv6addr> - Specify the value of the IPv6 source address.
mask - (Optional) Specify the mask.
<ipv6mask> - Specify the mask.
destination_ipv6 - Specify the value of the IPv6 destination address.
<ipv6addr> - Specify the value of the IPv6 destination address.
mask - (Optional) Specify the mask.
<ipv6mask> - Specify the mask.
tcp - Specify TCP.
src_port - (Optional) Specify the TCP source port range.
<value 0-65535> - Specify the value between 0 and 65535.
mask - (Optional) Specify the mask.
<hex 0x0-0xffff> - Specify the mask.
dst_port - (Optional) Specify the TCP destination port range.
<value 0-65535> - Specify the value between 0 and 65535.
mask - (Optional) Specify the mask.
<hex 0x0-0xffff> - Specify the mask.
udp - Specify UDP.
src_port - (Optional) Specify the UDP source port range.
<value 0-65535> - Specify the value between 0 and 65535.
mask - (Optional) Specify the mask.
<hex 0x0-0xffff> - Specify the mask.
dst_port - (Optional) Specify the UDP destination port range.
<value 0-65535> - Specify the value between 0 and 65535.
mask - Specify the mask.
<hex 0x0-0xffff> - Specify the mask.
icmp - Specifies that the rule applies to the value of ICMP traffic.
type - Specifies that the rule applies to the value of ICMP type traffic.
<value 0-255> - Enter the ICMP type value used here. This value must be between 0
and 255.
code - Specifies that the rule applies to the value of ICMP code traffic.
<value 0-255> - Enter the ICMP code value used here. This value must be between 0
and 255.
port - The access profile rule may be defined for each port on the switch. The port list is specified
by listing the lowest switch number and the beginning port number on that switch, separated
by a colon.
<portlist> - Specify a list of ports.
all - Specify that the access rule will apply to all ports.
vlan_based - Specify the VLAN-based ACL rule. There are two conditions: this rule will apply to