Lincoln Electric SVM135-B Welder User Manual


 
C-7
ACCESSORIES
C-7
POWER WAVE 455/POWER FEED 10
MAGNUM 200/300/400 GUNS
The easiest and least expensive way to use Magnum
200/300/400 guns with the Power Feed 10 wire feed-
er is to order them with the K466-10 connector kit, or
to buy a completely assembled Magnum gun having
the K466-10 connector (such as the K471-21, -22,
and -23 dedicated Magnum 400 guns and the K497-
20 and -21 Magnum 200 guns).
MAGNUM 550 GUNS
The easiest and least expensive way to use the
Magnum 550 guns with Power Feed 10 wire feeders
is to order the gun with the K613-7 connector kit, and
install a K1500-3 gun connection kit to the wire
feeder.
LINCOLN INNERSHIELD AND SUB ARC GUNS
All of these guns can be connected to the Power
Feed by using the K1500-1 Adapter Kit.
LINCOLN FUME EXTRACTION GUNS
The K556 (250XA) and K566 (400XA) guns require
that a K489-2 Fast-Mate™ adapter kit be installed.
Installation of this adapter also requires a K1500-1
gun connector kit.
The K206, K289, and K309 require only the installa-
tion of a K1500-1 connector in the Power Feed wire
feeder.
NON-LINCOLN GUNS
Most competitive guns can be connected to the
Power Feed by using one of the K1500 series
adapter kits.
K1500-1 (LINCOLN INNERSHIELD GUN
STANDARD CONNECTION)
Use this kit to connect the following guns: Guns hav-
ing a Lincoln standard innershield gun connector,
Fast-Mate™ guns with K489-2 Fast-Mate™ Adapter
Kit, Magnum 200/300/400 with K466-1 connector kit,
and Magnum 550 guns with the K613-1 gun connec-
tion kit.
K1500-2 (TWECO™ #2-#4 CONNECTION)
The K1500-2 gun adapter comes factory installed on
the Power Feed 10 wire feeder. Use this adapter for
guns that have a Tweco™ #2-#4 connector. Such
guns include Magnum 200/300/400 guns with K466-
10 connector kit, and completely factory assembled
Magnum guns that are factory equipped with the
K466-10 connector (such as the K497-21 dedicated
Magnum 400).
K1500-3 (TWECO™ #5 CONNECTION)
The K1500-3 gun adapter is for Magnum 550 guns
with a K613-7 connection kit, and any other gun hav-
ing a Tweco™ #5 connector.
K1500-4 (MILLER CONNECTION) for any gun hav-
ing a Miller connector.
Install gun adapters per the instructions shipped with
them.
CONDUIT ADAPTERS
K1546-1 ADAPTER
For use with Lincoln Magnum conduit (wire sizes
0.023 to 0.052)
Install the K1546-1 gun adapter at the incoming end
of the feed plate, secure with the set screw located at
the back of the feed plate. If a brass fitting is supplied
with the conduit, remove it from the feeder end of the
conduit by unscrewing it. Insert the conduit into the
K1546-1, secure the conduit by fastening it to the
adapter with the supplied knob screw.
K1546-2 ADAPTER
For use with Lincoln Magnum conduit (wire sizes
1/16 to 0.120)
Install the K1546-2 gun adapter at the incoming end
of the feed plate; secure with the set screw located at
the back of the feed plate. If a brass fitting is supplied
with the conduit, remove it from the feeder end of the
conduit by unscrewing it. Insert the conduit into the
K1546-2, secure the conduit by fastening it to the
adapter with the supplied knob screw.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC
Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC