Filter
Top Products
CHECKING MOUNTING SCREWS
At regular intervals, check every part for loose mounting
screws and tighten any loose screws found. Operating
the tool with loose screws will can be hazardous.
INSPECTING THE CONTACT ARM
Check if the contact arm can slide smoothly.
Clean the sliding area of the contact arm and use the
provided oil for lubrication from time to time.
This will enable a smooth operation and simultaneously
help to prevent the formation of rust.
PREPARATION FOR STORAGE
● When not in use for an extended period, apply a thin
coat of the lubricant to the steel parts to avoid rust.
● Do not store the nailer in a cold weather
environment. When not in use, the tool should be
stored in a warm and dry place.
● Keep out of reach of children.
● Refer to all instructions in the previous ‘Storage’
section of this manual.
SERVICE PARTS LIST
CAUTION: Repair, modification and inspection of
Bostitch Power Tools must be carried out by a Bostitch
Authorised Service Center.
The Parts List supplied with this tool will be helpful if
presented with the tool to the Bostitch Authorised
Service Center when requesting repair or other
maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
Stanley Bostitch tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
APPLICABLE LUBRICANTS
Use BOSTITCH Gas Nailer lubricant.
Do not use detergent oil or additives: these lubricants
will harm the O-rings and other rubber parts and will
cause the tool to malfunction.
NOISE AND VIBRATION DATA
NOISE EMISSION (See Tool Technical Data)
The characteristic noise values for the tool have been
determined in accordance with EN 12549 - “Acoustics -
Noise test code for fastener driving tools - Engineering
Method."
These values are tool related characteristic values and
do not represent the noise development at the point of
use. Noise development at the point of use will depend
for example on the working environment, the work piece,
the work piece support and the number of driving
operations, etc.
Depending on the conditions at the workplace and the
form of the work piece, individual noise attenuation
measures may need to be carried out, such as placing
work pieces on sound damping supports, preventing
work piece vibration by means of clamping or covering,
adjusting to the minimum air pressure required for the
job, etc.
INFORMATION ON VIBRATION (see Tool Technical
Data)
The characteristic vibration value for the tool has been
determined in accordance with ISO/WD 8662-11
"Measurement of vibration in hand held power tools -
Part 11 Fastener Driving Tools".
This value is a tool related characteristic and does not
represent the influence on the hand-arm system when
using the tool. An influence on the hand-arm system
when using the tool will depend for example on the
gripping force, the contact force, the working direction,
the adjustment of the compressed air supply, the work
piece, the work piece support, etc.
© Stanley Bostitch
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.