Filter
Top Products
Table of Contents
AWG710 Service Manual
v
Figure 4–1: Diagnostic menu 4–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–2: Calibration result message box (except option 02) 4–6. . . . .
Figure 4–3: EVENT IN connector pins and signals
and ground closure connector 4–9. . . . . . . . . . . . . . . . . . . . . . .
Figure 4–4: Loading file; selecting storage drive 4–10. . . . . . . . . . . . . . . . .
Figure 4–5: Cont mode initial test hookup 4–16. . . . . . . . . . . . . . . . . . . . . .
Figure 4–6: Triggered mode initial test hookup 4–18. . . . . . . . . . . . . . . . . .
Figure 4–7: Relationship between trigger signal
and waveform output 4–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–8: Relationship between gate signal and waveform output 4–21.
Figure 4–9: Amplitude accuracy initial test hookup 4–23. . . . . . . . . . . . . .
Figure 4–10: Direct DA output amplitude accuracy
initial test hookup 4–27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–11: Direct DA output pulse rise time initial test hookup 4–29. . .
Figure 4–12: Option 02 output amplitude accuracy
initial test hookup 4–31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–13: Optipn 02 output pulse rise time initial test hookup 4–33. . .
Figure 4–14: Pulse response initial test hookup 4–35. . . . . . . . . . . . . . . . . .
Figure 4–15: Trigger input initial test hookup 4–37. . . . . . . . . . . . . . . . . . .
Figure 4–16: Trigger signal and waveform output (+5 V check 1) 4–39. . .
Figure 4–17: Trigger signal and waveform output (+5 V check 2) 4–39. . .
Figure 4–18: Trigger signal and waveform output (–5 V check 1) 4–40. . .
Figure 4–19: Trigger signal and waveform output (–5 V check 2) 4–40. . .
Figure 4–20: Event input and enhanced mode initial test hookup 4–41. . .
Figure 4–21: Waveform while all ground disclosure
switches are open 4–42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–22: Waveform output when the SW1 is closed 4–43. . . . . . . . . . .
Figure 4–23: Waveform output when SW2 is closed 4–43. . . . . . . . . . . . . .
Figure 4–24: Waveform output when the SW3 is closed 4–44. . . . . . . . . . .
Figure 4–25: Waveform output when SW4 is closed 4–45. . . . . . . . . . . . . .
Figure 4–26: Initial waveform output 4–46. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–27: DC waveform output when the SW5 is closed 4–46. . . . . . . .
Figure 4–28: 1/4 Clock frequency and 10 MHz reference
input initial test hookup 4–48. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–29: Marker output initial test hookup 4–50. . . . . . . . . . . . . . . . . .
Figure 5–1: Accessing the service switch 5–4. . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–2: Hookup for the reference clock frequency adjustment 5–6. .
Figure 5–3: Hookup for the Marker level adjustment 5–7. . . . . . . . . . . . .
Figure 5–4: Hookup for the Marker level adjustment 5–10. . . . . . . . . . . . .