Filter
Top Products
Index
NI-DAQ FRM for PC Compatibles I-8
©
National Instruments Corporation
ND_SIMPLE_EVENT_CNT application,
2-217 to 2-218
ND_SINGLE_PERIOD_MSR
application, 2-218 to 2-220
ND_SINGLE_PULSE_GNR application,
2-227 to 2-229
ND_SINGLE_PULSE_WIDTH_MSR
application, 2-220 to 2-223
ND_SINGLE_TRIG_PULSE_GRN
application, 2-229 to 2-231
ND_TRIG_PULSE_WIDTH_MSR
application, 2-223 to 2-225
ND_TWO_SIGNAL_EDGE_SEPARATI
ON_MSR application, 2-225 to 2-227
GPCTR_Watch function, 2-245 to 2-247
grounding of DAC reference, 2-31
group digital I/O functions
DIG_Block_Check, 2-147
DIG_Block_Clear, 2-148
DIG_Block_In, 2-149 to 2-151
DIG_Block_Out, 2-152 to 2-153
DIG_Block_PG_Config, 2-154 to 2-157
DIG_DB_Config, 2-158 to 2-159
DIG_DB_HalfReady, 2-160 to 2-161
DIG_DB_Transfer, 2-162 to 2-163
DIG_Grp_Config, 2-164 to 2-165
DIG_Grp_Mode, 2-166 to 2-168
DIG_Grp_Status, 2-169 to 2-170
DIG_In_Grp, 2-171 to 2-172
DIG_Out_Grp, 2-178
DIG_SCAN_Setup, 2-188 to 2-191
H
handshaking functions
DIG_Grp_Mode, 2-166 to 2-168
DIG_Grp_Status, 2-169 to 2-170
DIG_Prt_Status, 2-186 to 2-187
DIG_SCAN_Setup, 2-188 to 2-191
high alarm deadband (figure), 2-65
I
ICTR_Read function, 2-248 to 2-249
ICTR_Reset function, 2-250
ICTR_Setup function, 2-251 to 2-254
Init_DA_Brds function, 2-255 to 2-262
default conditions for specific boards,
2-258 to 2-261
description, 2-255
device numbers, 2-255 to 2-257
initialization/utility functions
Align_DMA_Buffer, 2-22 to 2-24
Configure_HW_Analog_Trigger,
2-83 to 2-89
definition, 1-13
Get_DAQ_Device_Info, 2-195 to 2-196
Get_NI_DAQ_Version, 2-197
Init_DA_Brds, 2-255 to 2-262
Line_Change Attribute, 2-277 to 2-278
SCAN_Sequence_Setup, 2-304 to 2-306
Set_DAQ_Device_Info, 2-389 to 2-399
Timeout_Config, 2-400 to 2-401
interval counter/timer functions. See counter/
timer functions.
L
Lab/516/DAQCard-500/700 function support
(table), C-6 to C-8
Lab_ISCAN_Check function, 2-263 to 2-265
Lab_ISCAN_Op function, 2-266 to 2-269
Lab_ISCAN_Start function, 2-270 to 2-273
Lab_ISCAN_to_Disk function,
2-274 to 2-276
LabWindows function tree for data
acquisition, 1-6 to 1-12
8253 counter (ICTR) functions, 1-12
Am9513 counter (CTR) functions,
1-11 to 1-12
analog input functions, 1-7 to 1-8
analog output functions, 1-8 to 1-9
block transfer digital I/O functions, 1-10