National Instruments 321645c-01 Welding System User Manual


 
Index
©
National Instruments Corporation I-9 NI-DAQ FRM for PC Compatibles
configuration and calibration functions,
1-6
counter/timer functions, 1-11 to 1-12
DAQ-STC counters (GPCTR), 1-11
digital input/output functions, 1-9
event messaging functions, 1-12
group mode digital I/O functions, 1-10
initialization/utilities functions, 1-6
low-level analog input functions,
1-7 to 1-8
low-level waveform generation functions,
1-9
multiple-point analog input functions, 1-7
RTSI bus functions, 1-12
SCXI functions, 1-10 to 1-11
single-point analog input functions, 1-7
single-point analog output functions, 1-8
waveform generation functions, 1-9
Line_Change Attribute function,
2-277 to 2-278
low alarm deadband (figure), 2-66
LPM16_Calibrate function, 2-279
M
manual. See documentation.
memory transfer width, 2-37
Microsoft Visual Basic for Windows,
1-4 to 1-5
MIO and AI device function support (table),
C-1toC-5
MIO_Calibrate function, 2-280 to 2-283
MIO_Config function, 2-284 to 2-285
dithering, 2-284
Mode 0 through Mode 5 timing diagrams,
2-252 to 2-253
multiple-point analog input functions
AI_Read_Scan function, 2-14
AI_VRead_Scan function, 2-19
Configure_HW_Analog_Trigger,
2-83 to 2-89
DAQ_Check function, 2-115 to 2-116
DAQ_Clear, 2-117
DAQ_Config, 2-118 to 2-120
DAQ_DB_Config, 2-121
DAQ_DB_HalfReady, 2-122 to 2-123
DAQ_DB_Transfer, 2-124 to 2-125
DAQ_Monitor, 2-126 to 2-128
DAQ_Op, 2-129 to 2-131
DAQ_Rate, 2-132 to 2-133
DAQ_Set_Clock, 2-134 to 2-135
DAQ_Start, 2-136 to 2-139
DAQ_StopTrigger_Config,
2-140 to 2-141
DAQ_to_Disk, 2-142 to 2-144
DAQ_VScale, 2-145 to 2-146
definition, 1-13
Lab_ISCAN_Check, 2-263 to 2-265
Lab_ISCAN_Op, 2-266 to 2-269
Lab_ISCAN_Start, 2-270 to 2-273
Lab_ISCAN_to_Disk, 2-274 to 2-276
LabWindows function panel tree, 1-7
SCAN_Demux, 2-294 to 2-295
SCAN_Op, 2-296 to 2-299
SCAN_Sequence_Demux,
2-300 to 2-302
SCAN_Sequence_Retrieve, 2-303
SCAN_Sequence_Setup, 2-304 to 2-306
SCAN_Setup, 2-307 to 2-308
SCAN_Start, 2-309 to 2-314
SCAN_to_Disk, 2-315 to 2-318
Select_Signal, 2-372 to 2-388
multiplexing operations
AI_MUX_Config function, 2-10 to 2-11
SCXI_MuxCtr_Setup function,
2-347 to 2-348
SCXI_Single_Chan_Setup function,
2-366