Filter
Top Products
Index - 9
I
[O]
Operation errors .................................................. 3-27
Operation results inversion (INV) ........................ 5-15
Operation results pop (MPP) ............................... 5-12
Operation results push (MPS) ............................. 5-12
Operation results read (MRD) ............................. 5-12
Operation start (LD, LDI) ....................................... 5-2
OR ($=, $<>, $>, $<=, $<, $>=) (Character string data
comparisons) ....................................................... 6-11
OR (=, <>, >, <=, <, >=) (BIN 16-bit data comparisons)
............................................................................... 6-2
OR (A contact parallel connection)........................ 5-2
OR (D=, D<>, D>, D<=, D<, D>=) (BIN 32-bit data
comparisons) ......................................................... 6-4
OR (E=, E<>, E>, E<=, E<, E>=) (Floationg decimal
point data comparisons (Single precision)) ........... 6-6
OR (ED=, ED<>, ED>, ED<=, ED<, ED>=) (Floationg
decimal point data comparisons (Double precision))
............................................................................... 6-8
Or inverse (ORI) .................................................... 5-2
ORB (Ladder block parallel connections) ............ 5-10
ORF (Pulse parallel connection / trailing edge)
......................................................................... 5-5,5-7
ORI (B contact parallel connection)....................... 5-2
ORP (Pulse parallel connection / leading edge)
......................................................................... 5-5,5-7
ORPI, ORFI ........................................................... 5-8
Other convenient instructions ................................ 2-6
Other instructions ................................................ 5-55
Application instructions .................................... 2-29
Sequence instructions........................................ 2-6
OUT
Annunciator output (OUT F)............................. 5-28
Counters (OUT C)............................................ 5-26
High speed retentive timer (OUTH ST)............ 5-22
High speed timer (OUTH T) ............................. 5-22
Low speed retentive timer (OUT ST) ............... 5-22
Low speed timer (OUT T) ................................ 5-22
Output (OUT) ................................................... 5-20
Out instructions (OUT)......................................... 5-20
Output instruction table.......................................... 2-8
Output instructions (OUT).................................... 5-20
Output of sub-routine program OFF calls (FCALL)
........................................................................... 7-116
Output OFF calls between program files (EFCALL)
........................................................................... 7-125
Output reverse (FF) ............................................. 5-40
[P]
PAGE (No operation page change)..................... 5-57
Page change (NOPLF) ........................................ 5-57
Page change (PAGE n) ....................................... 5-57
Parallel connection (OR, ORI) ............................... 5-2
Parallel connections (ORB) ................................. 5-10
PCHK (Program low speed execution registeration
instruction) ......................................................... 7-384
PLF (Trailing edge output)................................... 5-37
PLOADP (Load program from Memory Card) ... 7-440
PLOW (Program low speed execution registration)
........................................................................... 7-382
PLS (Leading edge output).................................. 5-37
PLSY (Fixed cycle pulse output)........................ 6-162
POFF (Program output OFF standby instruction)
........................................................................... 7-378
Pointer branching instruction (CJ, SCJ, JMP) ... 6-129
Pop (MPP) ........................................................... 5-12
PR (Print ASCII code instruction) ...................... 7-166
PRC (Print comment instruction) ....................... 7-169
Print ASCII code instruction (PR) ...................... 7-166
Print comment instruction (PRC) ....................... 7-169
Program branch instruction table......................... 2-27
Program control instructions ................................ 2-56
Program execution control instruction table......... 2-27
Program low speed execition registration instruction
(PCHK) .............................................................. 7-384
Program low speed execution registration (PLOW)
........................................................................... 7-382
Program output OFF standby instruction (POFF)
........................................................................... 7-378
Program scan execution registration instruction
(PSCAN) ............................................................ 7-380
Program standby instruction (PSTOP) .............. 7-377
PSCAN (Program scan execution registration
instruction) ......................................................... 7-380
PSTOP (Program standby instruction) .............. 7-377
PSWAPP (Load + unload) ................................. 7-445
Pulse conversion
(DELTA) ........................................................... 5-42
(EGF, EGP)...................................................... 5-18
(MEF, MEP) ..................................................... 5-17
Pulse conversion of direct output (DELTA).......... 5-42
Pulse density measurement (SPD).................... 6-160
Pulse NOT operation start, pulse NOT series
connection, pulse NOT parallel connection LDPI,LDFI,
ANDPI,ANDFI,ORPI,ORFI) ................................... 5-7
Pulse operation results
Operation result conversions (MEF, MEP)....... 5-17
Pulse conversions of edge relay operation results
(EGF, EGP)...................................................... 5-18
Pulse operation start (LDF, LDP)..................... 5-5,5-7
Pulse parallel connection (ORF, ORP) ............ 5-5,5-7
Pulse series connection (ANDF, ANDP)................ 5-5
Pulse width modulation (PWM).......................... 6-164
PUNLOADP (Unload program from program memory)
........................................................................... 7-443
Push (MPS) ......................................................... 5-12
PWM (Pulse width modulation).......................... 6-164
[Q]
QCDSET (File setting for comments) ................ 7-342
QCPU dedicated instructions............................... 2-60
QDRSET(Setting files for file register use) ........ 7-339
[R]
RAD (Conversion from floating-point angle to radian
(Single precision)).............................................. 7-275