Filter
Top Products
E6581301
B-12
2
Terminal
symbol
Input/
output
Function (Sink Source logic)
Electrical
specifications
Inverter internal circuits
P24/
PLC
Output
24Vdc power output (when SW1 is in any
position other than PLC)
24V internal output terminal
24Vdc-200mA -
Input
If SW1 is turned to the PLC position, this
terminal can be used as a common terminal
when an external power supply is used.
- -
CC *1
Common
to input/
output
Digital signal equipotential (0V) terminal for the
control circuit and equipotential (0V) terminal
for an optional control power supply backup.
- -
PP Output Analog input setting power output
10Vdc
(Permissible load
current:10mAdc)
RR/S4 Input
SW3: Multifunction programmable analog input
terminal when SW3 is in the RR position.
Standard default setting:0~10Vdc input and
0~60Hz frequency.
10Vdc
(Internal impedance:30 k)
VI/I I Input
Multifunction programmable analog input.
Standard default setting: 0~10Vdc input and
0~60Hz frequency.
This terminal can also be used as a 4-20mAdc
(0-20mAdc) input terminal, if the parameter
H set to .
10Vdc
(Internal impedance:30 k)
4~20mA
(Internal impedance:242)
RX Input
Multifunction programmable analog input.
Standard default setting:0~±10Vdc input and
0~±60Hz frequency.
10Vdc
(Internal impedance:22 k)
FM Output
Multifunction programmable analog output.
Standard default setting: output frequency
Use this terminal to connect a 1mAdc full-scale
ammeter. This terminal can also be used as a
0-10V (H=) or 0-20mA terminal
(H=), if the SW2 switch is set to
0-10V/0-20mA side.
1mA full
-
scale DC
ammeter (Allowable
load resistance 7.5k or
less) or 7.5Vdc-1mA
full-scale DC voltmeter
0-10V full-scale DC
voltmeter (Allowable
load resistance 500 or
more)/0-20mA (4-20mA)
Full-scale DC ammeter
voltmeter (Allowable
load resistance 500 or
less
)
AM Output
Multifunction programmable analog output.
Standard default setting: output current
Use this terminal to connect a 1mAdc full-scale
ammeter or 7.5Vdc (10Vdc)-1mA full-scale
voltmeter.
1mA full
-
scale DC
ammeter ammeter
(Allowable load
resistance 7.5k or
less) or 7.5Vdc-1mA
full-scale DC
voltmeter
OUT1
Output
Multifunction programmable open collector
output. The default setting is to output a signal
when output low speed threshold has been
reached. Depending on the SW4 setting,
pulses are output with frequencies of 1.00kHz
to 43.20kHz. Standard default setting:3.84kHz
Open collector output
24Vdc-50mA
*Sink logic/source
logic switchable
OUT2
Multifunction programmable open collector
output. By default, it is set to output a signal
indicating the completion of acceleration or
deceleration.
NO
Digital output signal equipotential (0V) terminal
for the control circuit. It is isolated from the CC
terminal.
CCA
*1
Common
to input/
output
Analog input/output signal equipotential (0V)
terminal for the control circuit.
- -
*1: Although the CC terminal and the CCA terminal are not insulated, they should be used separately, one for the logic circuit and
the other for the analog circuit
P15
15k
7k
P5
15k
15k
242
S4
P5
RR
SW3
12.7k
2.2k
15k
SW2
+
-
+
-
4.7k
120
70
0
-
1
mA
0-20mA
0-10V
0-20mA
0-10V
4.7k
+
-
20
P24
OUT1
OUT2
SW4 PULS
LO
20
NO
15V
Constant
voltage
circuit