Filter
Top Products
Contents for MDS-C1 Series SPECIFICATIONS MANUAL (BNP-C3040D)
Appendix 3-3 Example of servo selection .................A3-7
Appendix 3-3-1 Motor selection calculation.........................A3-7
Appendix 3-3-2 Servo selection results...............................A3-10
Appendix 3-3-3 Motor shaft conversion load torque............A3-11
Appendix 3-3-4 Expressions for load inertia calculation......A3-12
Appendix 3-4 Selecting the power supply .................A3-13
Appendix 3-4-1 Selecting according to the continuous rated
capacity.....................................................A3-13
Appendix 3-4-2 Selection with maximum momentary capacity
..................................................................A3-14
Appendix 3-4-3 Selection example......................................A3-15
Appendix 4. Explanation of Large Capacity Spindle Unit
Specifications
Appendix 4-1 Explanation of large capacity spindle unit
specifications.......................................A4-2
Appendix 4-1-1 Outline.......................................................A4-2
Appendix 4-1-2 List of units.................................................A4-2
Appendix 4-1-3 Selection of AC reactor (B-AL),
contactor and NFB ....................................A4-2
Appendix 4-1-4 Outline dimension drawings.......................A4-3
Appendix 4-1-5 Panel cut dimension drawing.....................A4-8
Appendix 4-1-6 Heating value.............................................A4-9
Appendix 4-1-7 Selecting the power capacity .....................A4-9
Appendix 4-1-8 Selecting the wire size...............................A4-9
Appendix 4-1-9 Drive unit connection screw size................A4-10
Appendix 4-1-10 Connecting each unit...............................A4-10
Appendix 4-1-11 Restrictions..............................................A4-12
Appendix 4-1-12 Parameters..............................................A4-14
Appendix 4-1-13 Precautions..............................................A4-14
Appendix 5. Transportation Restrictions for Lithium Batteries
Appendix 5-1 Transportation restrictions
for lithium batteries ..............................A5-2
Appendix 5-1-1 Target products..........................................A5-2
Appendix 5-1-2 Handling by user........................................A5-3
Appendix 5-1-3 Regulations enforcement timing.................A5-4
Appendix 6. Compliance to EU EC Directives
Appendix 6-1 Compliance to EC Directives ..............A6-2
Appendix 6-1-1 European EC Directives.............................A6-2
Appendix 6-2-2 Cautions for EC Directive compliance ..........A6-2
Appendix 7. EMS Instruction Guidelines
Appendix 7-1 Introduction.........................................A7-2
Appendix 7-2 EMC instructions.................................A7-2
Appendix 7-3 EMC measures...................................A7-3
Appendix 7-4 Measures for panel structure.............. A7-3
Appendix 7-4-1 Measures for control panel unit..................A7-3
Appendix 7-4-2 Measures for door......................................A7-4
Appendix 7-4-3 Measures for operation board panel..........A7-4
Appendix 7-4-4 Shielding of the power supply input section
..................................................................A7-4
Appendix 7-5 Measures for various cables...............A7-5
Appendix 7-5-1 Measures for wiring in panel......................A7-5
Appendix 7-5-2 Measures for shield treatment ...................A7-5
Appendix 7-5-3 Servomotor power cable............................A7-6
Appendix 7-5-4 Servomotor feedback cable.......................A7-6
Appendix 7-5-5 Spindle motor power cable ........................A7-7
Appendix 7-5-6 Spindle motor feedback cable....................A7-7
Appendix 7-6 EMC countermeasure parts................A7-8
Appendix 7-6-1 Shield clamp fitting.....................................A7-8
Appendix 7-6-2 Ferrite core................................................A7-9
Appendix 7-6-3 Power line filter..........................................A7-10
Appendix 7-6-4 Surge protector..........................................A7-15
Appendix 8. Instruction Manual for Compliance with UL/c-UL
Standard
Appendix 8. Instruction Manual for Compliance
with UL/c-UL Standard ........................A8-2
Appendix 9. Compliance with China Compulsory Product
Certification (CCC Certification) System
Appendix 9-1 Outline of China Compulsory Product
Certification System ............................ A9-2
Appendix 9-2 First Catalogue of Products subject to
Compulsory Product Certification........ A9-2
Appendix 9-3 Precautions for Shipping Products .....A9-3
Appendix 9-4 Application for Exemption................... A9-4
Appendix 9-5 Mitsubishi NC Product Subject to
/Not Subject to CCC Certification........A9-5
(Note) This is the content for SPECIFICATION MANUAL version D. The structure of section and page number may be different
other than version D.